How To Match Of Old Popcorn Ceiling Color To New Repair

Love it or hate it, many homes accept the traditional popcorn ceiling texture, its inexpensive and it does the trick. What many people don't realize is that spraying this texture is actually incredibly easy and a perfect project for whatsoever DIY Painter.

Whether you have to do a modest repair, a whole room or even a whole house, spraying popcorn ceiling texture is all about keeping a steady arm and a consistent texture mix.

The all-time part virtually this project is that it's really quite inexpensive to do every bit well. All information technology requires for purchase is a handbag of ceiling texture mix, prep materials such as plastic and tape and finally a texture sprayer.

A quick notation about texture sprayers. For the DIYer, I recommend the Wagner Ability Tex Texture Sprayer. The reason for this is that information technology is a meaty all in 1 unit that does exactly what it says it will do and it doesn't price a fortune (usually around $lxxx – $90). I prefer this over texture hoppers that crave air compressors because they require compressors with a really high CFM. Fifty-fifty if you have a large compressor, do yous actually desire to haul it into the house?

Tools & Materials

Texture Sprayer (Wagner Spray Tex)
Pocketbook of Popcorn Ceiling Texture
Painters Plastic
Tape
Minor Ladder
Spray Can of Primer

Step 1: Prepare Your Work Area

The start step in any project is to prep your area and make sure it is ready for your project. Start by removing everything from from the room. This includes furniture, wall hangings, everything possible.

Next, I similar to set up an area with all of my work tools set neatly out and organized. This helps me brand sure I have everything I need for my project before I go started and helps me keep track of all my tools and materials during the project.

Step 2: Encompass Your Walls

Spraying popcorn texture is incredibly messy, unless you plan on repainting your walls when you are finished, you will want to comprehend them 100%.

The easiest mode to cover your walls is to start with a roll of 2″ low tack tape (such every bit Frog Tape Fragile Surface). I use depression tack because this tape will be applied directly to your wall and you lot don't want it to pull whatever paint off your wall every bit yous remove it. Rip off a 2′ piece of tape and identify it on the wall correct where information technology meets the ceiling. Y'all volition want the record perfectly in the corner where the wall meets the ceiling. Next, press the top 1/2 inch of the record firmly to the wall trying hard to make sure the bottom 1″ of the tape is loose (we'll be attaching plastic to this next). Run the tape around all of the walls in the room you are working on.

Now, take your painters plastic and pull out plenty to get all the fashion around the room you lot are working on. Unfold the plastic and carefully attach the acme of the painters plastic to the bottom 1″ of the painters tape that you merely ran around the room. Pull the plastic downwardly your walls and make certain it goes all the fashion past your base trim.

Step 3: Embrace Your Floors

When spraying ceilings, I prefer not to use regular canvas driblet cloths to cover the floors. And then much texture falls to the floor and makes a mess that I prefer to cover the floors with a plastic drop material that tin can exist rolled upward and thrown abroad when done rather than trying to make clean off my drib cloths.

To make sure that no portin of your flooring is left uncovered, lift up the plastic that you lot have hanging from the walls and run some other strip of tape on acme of all of the baseboard in the room you are working on. Pull out some other large sheet of painters plastic and this time pull out the plastic and use information technology to cover the floors. Attach the edges of the painters plastic to the tape you just ran around the room on the baseboard to keep if from moving around while y'all work. You must make sure to non pull the plastic too tight equally you tack it to the tape or this will cause it to rip and tear. Brand sure it is loose to forbid this.

Stride 4: Preparing The Ceiling For Sprayer

Brand certain your ceiling is 100% set up for ceiling texture before spraying. A few tips:

Popcorn texture won't cover up a rough ceiling. Make certain your drywall piece of work is good and smooth.
If y'all are doing repairs, make sure any loose texture has been removed. Otherwise one time yous beginning spraying, the old texture can go loose and offset falling off.
If y'all are repairing water damage, make sure to prime the damaged areas with an oil based primer.

Step five: Prepare Your Texture & Sprayer

Depending on how big of an area you are spraying, you will desire to prepare enough texture for the entire job at once. I like to mix my ceiling texture in a five gallon saucepan and a mixer that attaches to a drill for like shooting fish in a barrel mixing.

Keep calculation water to your mix until your popcorn mixture is runny, but non quite to a watery texture. It cannot be too thick or it volition not spray out of your texture sprayer, if information technology is also thin information technology volition splatter on your ceiling. A skilful idea is to start with a pocket-size batch and do a few sample sprays on a big slice of cardboard.

If you lot are repairing a spot on an existing ceiling, make certain that your new texture matches your old texture. Typically texture comes in fibroid, medium and fine.

Stride 6: Spray The Ceiling

At present that your room is prepped and your texture is ready to go, it's time to finally spray on your popcorn texture.

Just similar spraying with paint, spray your texture in long even strokes that overlap by roughly l%. Start each stroke most 12″ before the area y'all programme on spraying and finish each stroke about 12″ afterwards the area. This volition help to blend the area in.

While you lot are spraying, you arm will probable become exhausted very quickly as information technology is not used to this type of work. Use a small stride ladder to get yourself closer to the ceiling and antipodal energy in your arm.

If you are trying to repair a small surface area in the center of a ceiling, spray the new texture out 2-3′ into the old texture to help blend the one-time and new together.

The real play a trick on is finding a balance where your texture isn't too thin or too thick. The best manner to do this is to practice on a piece of plywood or paper-thin before working on your bodily project. Y'all can spray and re-spray this piece until you find the perfect amount of texture that you are looking for.

Step 7: Cleanup

If you lot properly prepped your work area, then cleanup should be like shooting fish in a barrel. Simply remove your tools, wash your texture sprayer and wrap upwardly all of your plastic into a big ball. Hopefully afterwards you pull your plastic there won't be any areas that were missed!